一、冷庫整體拼裝時應與墻體及屋頂留有間隙，冷庫地板安裝平整，不平處用材料把地坪墊平，并鎖緊板與板之間鎖鉤，用硅膠密封，達到庫面平整，無空心感，冷庫庫體的頂板、地板、立板安裝好后，頂與立、立與地板之間修正平齊并鎖緊，彼此間所有鎖鉤。
A cold, the whole assembly should be with the walls and roof gaps, cold floor installation flat, the uneven floor pad material, and the locking plate and the lock hook plate, seal with silicone, reach the base surface is smooth, no hollow, roof, floor and the vertical plate installed after the cold storage between the top and the vertical, vertical, and modified floor flush and locked each other all lock hook.
1、選擇吊點位置時，首先考慮空氣循環 的位置，其次在考慮庫體結構方向。
1. When selecting the position of the lifting point, the position of the air circulation is considered first and the direction of the structure of the reservoir is considered.
2、冷風機與庫板間隙要大于冷風機的厚度。
2, the gap between the cooling fan and the plate is greater than the thickness of the air cooler.
3、冷風機所有吊栓應全部緊固，并用密封膠將螺栓及吊栓穿孔封閉，防止冷橋和漏氣。
3. All the hoisting bolts of the air cooler should be all fastened, and the bolts and hoisting bolts are sealed with sealant to prevent the cold bridge and air leakage.
4、吊頂風機過重時，應用4號角或5號角鐵做過梁，過梁應橫跨到另一塊頂板和墻板上，以減輕承重。
4, the ceiling fan is overweight, 4 horn or No. 5 angle lintel lintel should do, across to another piece of roof and wall panels, to reduce the load.
二、制冷機組的組裝安裝技術：
Two. The assembly and installation technology of the refrigerating unit:
1、半封或全封閉壓縮機都應安裝油分離器，并在油分內加住適量機油，蒸發溫度低于—15度時，應加裝氣液分離器并加裝適量冷凍機油。
1, semi closed or full closed compressor oil separator should be installed, and the amount of oil in the oil business and live, evaporation temperature is below - 15 degrees, should install the gas-liquid separator and add the amount of refrigerant oil.
2、壓縮機底座應安裝減震膠座。
2, the base of the compressor should be fitted with a damping rubber seat.
3、機組的安裝要留有維修空間，便于觀察儀表和閥門的調節。
3, the installation of the unit should have room for maintenance, so that it is convenient to observe the adjustment of the instrument and valve.
4、高壓表應安裝在儲液灌閥門三通處。
4. The high pressure meter should be installed at the three place of the liquid storage valve.
5、機組整體布局合理，顏色一致。各型號機組安裝結構應保持一致。
5. The whole layout of the unit is reasonable and the color is consistent. The installation structure of each type of unit should be consistent.
本文的精彩內容來自山東冷庫造價詳細內容請點擊我們的官方網站:http://www.sddslk.com謝謝您的到來!
The wonderful content of this article comes from the detailed content of the cost of Shandong cold storage. Please click on our official website: http://www.sddslk.com thank you for your arrival.
魯公網安備 37010402001149號 網站地圖 XML
